Dantherm CDP 50 built-in dehumidifier

Dantherm CDP 50 built-in dehumidifier
Recommended retail price 2024 starting from :
5560 €
Our Price starting from :
5560 € Including VAT
Ref. Abatik 023550
Ref. Provider CDP 50T
DANTHERM CDP 50 T standard built-in dehumidifier
Built-in dehumidifier perfect for indoor pools with a maximum surface area of 30 m²
Capacity 3,2 l/h
Integrated hygrostat,
Available with integrated heater,
Remote control on option
In stock
DANTHERM CDP 50 T standard built-in dehumidifier
Ref. Abatik 023550 Ref. Provider CDP 50T
EUR 5560
5560 €
Order Free quote
DANTHERM CDP 50 T built-in dehumidifier with hot water battery
Ref. Abatik 023556 Ref. Provider CDP 50T+094334
EUR 6400
6400 €
Order Free quote
DANTHERM CDP 50 T built-in dehumidifier with electric heater
Ref. Abatik 023553 Ref. Provider CDP 50T+094337
EUR 5990
5990 €
Order Free quote
Wall crossing kit + aluminium grills for DANTHERM CDP 50 T built-in dehumidifier
Ref. Abatik 023559 Ref. Provider 094243
EUR 795
795 €
Order Free quote
DRC 1 remote control for DANTHERM CDP
Ref. Abatik 023547 Ref. Provider 093455
EUR 335
335 €
Order Free quote
The CDP has been specifically developed for spas, hammams, verandas, libraries, museums and sports facilities. In brief, this unit is suitable for any environment which requires precise humidity control in a residential or public situation.

Humidity present in the ambient air is suctioned by the ventilator which is integrated into the dehumidifier. Air which passes through the evaporator is cooled to below condensation point, water vapour is then condensed and evacuated. Dry air passes on the condenser, is heated and then is sent into the ambient atmosphere.

Following dehumidification treatment, ambient air temperature gains approximately 5°C.

The dehumidifier is entirely automatic. Very quiet to run and controlled by an integrated hygrostat. A digital control panel clearly shows operational modes. Easy to maintain, just lift off the front panel to clean the air filter.
Operational schema dehumidifier

Dantherm CDP 50 built in dehumidifier

Remote control

(On option)
The CDP can be equipped with a wireless remote that indicates the humidity rate and temperature of the room.
The DRC1 distance control unit features an "installation mode" that can regulate heating system temperature and evacuating ventilation. It is also possible to connect the distance control unit to the CDP dehumidifier printed circuit board.
If the model you have chosen has featured heating, the ventilator automatically starts when the heater starts.
The distance control can be "locked" to avoid any unwanted modification to your settings.
Remote control for Dantherm CDP dehumidifiers

The Dantherm CDP 50 built-in unit is installed next to the room that requires dehumidification. Ambient ventilation is fed through using a wall crossing that operates using a ventilation suction and a ventilation discharge grill. The heater that can be incorporated optionally by choosing the hot water battery or heater models. This can control the humidity rate of indoor pools by dehumidifying on a closed circuit.
A passive defrosting system is integrated into the electronic control. A sensor situated on the unit's evaporator ensures defrosting only when required. When in defrost mode, the compressor stops and the ventilator sends ambient air onto the evaporator, which is, in turn, defrosted.
The CDP 50 operates automatically by electronic control and incorporated hygrostat. The hygrostat is factory set to a relative humidity rate of approximately 60%.
The digital control panel indicates various unit status :
1. The unit is connected to its power source
2. Dehumidification - the compressor is in operation
3. Cooling circuit error - the dehumidifier is not in operation
4. The heating battery is connected (for models which feature hot water battery)


CDP 50 built-in
Air flow
Electrical supply
230 V (Ph+N)
Electrical capacity
1,5 W
6,6 A
Dehumidification at 30°C - 80% H.R.
77 L/day
Dehumidification at 28°C - 60% H.R.
52 L/day
Dehumidification at 20°C - 60% H.R.
26 L/day
Decibels measured at 1m
44 dBa
Cooling liquid
Quantity of gas
0,9 kg
Indice of protection
(1) Hot water battery option (kW)
Heater option (kW)

(1) Information based on primary circuit water temperature at 80/60°. Ambient air 28°, relative humidity rate 60%.

Operational limits

Ambient temperature
10 - 36 °C
Ambient humidity rate
40 - 100 % H.R.

Dimensions and weight

Depth x height x width
304 x 700 x 1148 mm
57,5 Kgs

Front panel dimensions Dantherm CDP 50 built in dehumidifier
Back panel dimensions Dantherm CDP 50 built in dehumidifier

Dimensions of wall crossings and ventilation grills

/ (mm)6161148791

Dimensions grills Dantherm CDP 50 built in dehumidifier


High quality product
Bodywork made from galvanised steel, painted on inner and outer surfaces.
Discreet installation
Aluminium ducts and grills for enhanced, discreet installation.
Low energy consumption
Rotary compressor and radial ventilator.
Very quiet in operation
44 decibels measured at 1 meter from the dehumidifier.

Examples of installation

DANTHERM CDP 40 built in dehumidifier
DANTHERM CDP 40 built in dehumidifier
DANTHERM CDP 40 built in dehumidifier


2 years

Photos non-contractual
Price incl. VAT

Ask for a free quote dantherm cdp 50 built-in dehumidifier

Other product : Dantherm CDP 50 built-in dehumidifier
Starting from 5560 eur Including VAT.

Please fill in this form carefully. Our commercial service will handle your request promptly.

UK freephone hotline

Monday Friday 9.00 19.00, Saturday 10.00 18.00

contact tel